Napoleon 28" Havelock Direct Vent Gas Stove

Napoleon Wall Terminal Kit for Direct Vent Gas Stoves

• Terminal Kit
• Helps terminate a direct vent piping system
• Includes: One 7 Inch Vent Termination, One Adjustable Pipe from 28 Inch to 54 Inch, One 24 Inch Pipe, One 90° Elbow, One 10 Feet 4 Inch Aluminum Flex Vent with Spacers, One Fire Stop, One Black Trim Collar and Three Decorative Metallic Black Bands
• For use with Direct Vent Gas Stoves

Napoleon 24" Through the Wall Vent Kit for Direct Vent Gas Stoves

• Through the Wall Vent Kit
• Allows safe venting through a wall
• For use with GDS20 and GDS25 gas stoves
• Includes: Mounting Plate, Black Trim Collar, 45° Elbow and Terminal

Napoleon Periscope Vent Kit for Direct Vent Gas Stoves

• Periscope Vent Kit
• Helps terminate a direct vent piping system
• Includes: One Periscope GD201, One Adjustable Pipe from 28 Inch to 54 Inch, One 24 Inch Pipe, One 90° Elbow, One 10 Feet 4 Inch Aluminum Flex Vent with Spacers, One Fire Stop, One Black Trim Collar and Three Decorative Metallic Black Bands
• Intended for Napoleon's 4 Inch x 7 Inch Direct Vent gas stoves

Napoleon Duravent Adaptor for Direct Vent Gas Stoves

• Napoleon GDS924N Simpson DuraVent Adapter
• Allows a Napoleon 4" x 7" gas stove to be used with Simpson DuraVent gas stove venting components

Napoleon B-Vent Adaptor Kit for Direct Vent Gas Stoves

• For use with GDS28/50/60 gas stoves
• Includes spill switch and decorative metallic black band
• Converts a Napoleon B-Vent gas stove for use with a direct vent components

DuraVent Wall Thimble

• Use with Square Horizontal Cap only.
• Provides a complete wall-pass-through and firestop.
• Refer to the appliance manufacturer’s installation instructions for requirements.
• May be required in Canada.

DuraVent Cathedral Ceiling Support Box

• Use to pass through ceiling and support pipe.
• May be used on vaulted or flat ceilings.
• Painted black.
• Trim and clamp included.

DuraVent Ceiling Firestop

• Required for multi-story vertical installations on the second floor and any subsequent floors.
• 4"x 6 5⁄8" style may vary.

DuraVent Attic Insulation Shield

• Required for installations that pass through an attic to prevent insulation and debris from accumulating near the vent.
• Provides 1” clearance to combustibles.
• Includes base w/tube, extension tube, and collar.

DuraVent Storm Collar

• Use to maintain a weather-tight resistant seal between the pipe and the flashing.

DuraVent High-Wind Termination Cap

• Available in aluminum.
• Use for vertical terminations only.
• For vertical terminations only.
• Provides improved performance in high wind conditions.

DuraVent Decorative Cover

• Use as a decorative cover for horizontal (through-wall) installations Fits over the Wall Thimble faceplate.
• Also used to cover a Ceiling Support Box. Comes with an insulation ring to reduce air infiltration where the pipe slips through the thimble.
• Painted black.

DuraVent DirectVent Pro Vinyl Sliding Standoff

• Use as a heat shield on structures with vinyl siding, or other temperature-sensitive materials, to help prevent warping and or melting of the material.
• Use only on horizontal terminations and on any irregular surfaced siding (ie: shiplap siding, shake shingle siding) so the cap is not embedded in the siding.

DuraVent Square Horizontal Termination Cap

• Available in aluminum, stainless steel (S), and copper (C).
• Use for standard and high-wind through-the-wall termination.
• Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.

DuraVent 90-Degree Adjustable Type B Gas Vent Elbow

• Offsets obstructions as needed.
• Elbows (3”-8”) swivel 360° at the base.
• 90° Elbow is adjustable from 0° to 90° in sizes 3”-10”.
• Elbows must be supported when installed.

DuraVent 45/60-Degree Adjustable Type B Gas Vent Elbow

• Offsets obstructions as needed.
• Elbows swivel 360° at the base.
• 45°/60° Elbow is adjustable from 0° to 60°.
• Elbows must be supported when installed.

DuraVent 3"-8" Aluminum Type B Gas Vent Firestop Spacer

• Use at every ceiling level where Square Firestop Support is not used.
• 3”-6” style is shown in the left photo.
• 7”-12” style is shown in the right photo.

DuraVent 3"-8" Aluminum Type B Gas Vent Square Firestop Support

• Straps extend 16”.
• Use to support vent at ceiling level.
• Provides the mandatory 1” clearance to combustibles.
• Includes clamp that supports and prevents pipe sections from slipping down.

DuraVent 3"-8" Galvalume Type B Gas Vent Adjustable Roof Flashing

• Use to weatherproof the penetration of vent pipe through the roof.
• Select roof flashing based on the pitch of the roof.
• For pitches of 0/12 - 6/12.
• Storm Collar required.
• Made of galvalume.

DuraVent 3"-8" Aluminum Type B Gas Vent Tall Cone Flat Flashing

• Use to weatherproof the penetration of vent pipe through the roof.
• Use on flat roofs, chase enclosures, or masonry chimneys.
• Select roof flashing based on the pitch of the roof.
• Storm Collar required.
• Made of galvalume.

DuraVent 3"-8" Aluminum Type B Gas Vent Steep Roof Flashing

• Use to weatherproof the penetration of vent pipe through the roof.
• Select roof flashing based on the pitch of the roof.
• For pitches of 7/12 - 12/12.
• Storm Collar required.
• Made of galvalume.

DuraVent 3"-8" Aluminum Type B Gas Vent Storm Collar

• Use to maintain a weather-tight resistant seal between the pipe and the flashing.

DuraVent 3"-8" Aluminum Type B Gas Vent High-Wind Cap

• For vertical terminations only.
• Use for vertical terminations only.
• Provides improved performance in high wind conditions.

DuraVent 3"-8" Galvanized Steel Type B Gas Vent Wall Strap

• Use to provide support for offsets and horizontal runs.
• Recommended every 4’ to support vertical common vent.
• Use also with DuraConnect or DuraConnect II.
• Wall Strap legs can be rotated 360˚ to conceal the screw.
• 10” Type B gas vent (11” OD) uses a 7” DuraPlus Chimney Wall Strap.